Fashion Universal Leather Seat Covers Full Set with Rivet

Fashion Universal Leather Seat Covers Full Set with Rivet is a 7-piece seat-cover set for compatible 5-seat passenger vehicles. It combines leatherette panels with decorative metal rivets and stitched sections, covering the front and rear seating areas without replacing the original upholstery.

The cover uses a layered construction of leatherette, high-resilience sponge, non-woven fabric and anti-slip silicone. The combination provides a smooth seating surface, cushioning between the cover and the original seat, and additional friction on the underside.

Black Universal Car Seat Covers use a black base with stitched panel lines and metal rivet details. The relatively thin profile keeps the cover visually close to the original seat instead of creating the raised appearance associated with thick seat cushions.

Black Leather Seat Covers for Cars are available with front-seat storage pockets, elastic fastening sections and reserved areas around the side-airbag position. The rear section uses a long bench cover and separate backrest pieces to accommodate compatible rear-seat layouts.

Product Structure

The seat cover is constructed from several functional layers. The outer leatherette forms the visible seating surface, while the sponge layer adds cushioning. Non-woven fabric provides backing support, and the anti-slip silicone layer sits against the original upholstery.

Metal rivets are attached to selected stitched sections rather than distributed across the entire surface. This keeps the decorative treatment concentrated around the panel structure and leaves the main seating area relatively clear.

Rivet & Stitching Details

Metal Rivet Placement

The rivets follow selected panel lines on the front seat covers. Their placement is coordinated with the stitching so the decorative elements remain integrated with the cover construction.

Panel Stitching

Stitched sections divide the leatherette surface into individual panels. The stitching also helps define the shape of the cover around the seat surface.

Perforated Sections

Selected areas of the seating surface use perforated material. These sections provide a different surface texture and allow air to move through the perforated portion of the cover.

Low-Profile Construction

The layered material is arranged in a relatively slim format. This allows the seat cover to add surface protection and cushioning without forming a thick independent cushion on top of the original seat.

Front Seat Configuration

The front section consists of separate backrest and seat-base covers. Elastic sections, straps and hooks are used to position the covers around the original seat structure.

Side-Airbag Reserved Area

The front covers include a reserved area around the side-airbag position. Because seat construction and airbag locations differ between vehicles, compatibility should be checked against the specific vehicle before installation.

Rear Storage Pocket

A storage pocket is integrated into the back of the front seat cover. It can be used for small items such as phones, keys, documents and magazines.

Elastic Adjustment

Elastic sections allow the front covers to accommodate variations in seat shape. Straps and hooks provide additional fastening points underneath the seat.

Headrest Coverage

The front configuration includes matching headrest covers. The headrest pieces are installed separately after removing the original headrests.

Rear Seat Layout

The rear section uses two backrest covers and one long bench cover. This configuration is intended for compatible rear benches with an approximate seat width of 50-56 inches.

Long Bench Coverage

The single rear bench section provides coverage across the main seating surface. Actual fit depends on the width, contours and fixing points of the original rear seat.

Separate Rear Backrests

The two rear backrest pieces allow the cover to follow common split-back seat arrangements. The fastening points should be aligned with the original seat structure during installation.

Safety Access

Openings and reserved areas are provided where required for seatbelt and other original seat functions. These functions should be checked after the cover has been fitted.

Color & Surface Options

Black

Brown

Pink

Red

The available colors use the same rivet and stitched-panel construction. Color selection may vary according to the specific production configuration.

Technical Specifications

Material and Functional Details

Leatherette Outer Layer

The leatherette surface forms the visible part of the cover. It provides a smooth material surface and can be cleaned with a damp cloth during routine use.

Resilient Sponge Layer

The sponge layer is positioned beneath the outer material to provide additional cushioning between the cover and the original seat.

Non-Woven Backing

The non-woven layer supports the upper materials and separates the sponge from the underside construction.

Anti-Slip Silicone Base

The silicone layer increases contact friction with the original upholstery and helps limit movement while entering, exiting and sitting in the vehicle.

Metal Rivet Components

The rivets are used as surface decoration and are positioned according to the stitched panel layout. The finished product should be inspected for secure rivet attachment before packing.

Fitment Considerations

This is a universal-fit product rather than a vehicle-specific molded cover. Before ordering, the seat dimensions, headrest shape, rear-seat configuration and available fastening points should be compared with the product dimensions.

For vehicles equipped with side airbags, the position and construction of the front-seat reserved area should also be checked. A universal seat cover should not obstruct the original airbag deployment path or seatbelt operation.

The rear bench section is designed for approximately 50-56 inch seat widths, but the actual fit can vary according to seat contours, center-console structure and split configuration.

Installation

The covers are secured with elastic sections, straps, plastic chucks and hooks. The original seats normally do not need to be removed during installation.

Installation time is approximately 30-60 minutes depending on vehicle configuration and installer experience.

Installation Sequence

1. Remove the front headrests and install the matching headrest covers.

2. Position the front backrest and seat-base covers over the original seats.

3. Route the straps underneath the seats and connect the plastic chucks and hooks.

4. Adjust the elastic sections so the cover follows the seat surface.

5. Install the two rear backrest covers and long rear bench cover.

6. Check the seatbelt openings, headrests, fastening points and side-airbag areas before use.

Package Contents

2 x Front Backrest Covers with Headrest Covers

2 x Front Seat Base Covers

2 x Rear Backrest Covers with Headrest Covers

1 x Rear Long Bench Cover

1 x Bag of Plastic Installation Chucks & Hooks

Total: 7 Main Seat-Cover Pieces

Cleaning and Maintenance

For routine cleaning, wipe the leatherette surface with a damp cloth and allow it to dry naturally. Remove dust and small particles before wiping to reduce surface abrasion.

Bleach, abrasive cleaners, strong solvents and high-temperature drying should be avoided because they may affect the surface finish, stitching or decorative rivets.

Quality Control and Production

Red Rain applies production and inspection procedures covering the main components of the seat-cover assembly. Checks may include leatherette surface condition, color consistency, stitching, panel alignment, rivet attachment, fastening components and finished-product appearance.

The production facility operates under an ISO 9001 quality management system. Reported production capacity is approximately 90,000 units per month, depending on product configuration and production scheduling.

Wholesale and Private Label

Red Rain supplies Fashion Universal Leather Seat Covers Full Set with Rivet for automotive accessory distributors, retailers, car interior shops and private-label buyers.

Available project options include color selection, stitching adjustments, logo application, private-label packaging and bulk production. Samples can be produced before larger orders when material, color or construction details need to be confirmed.

Order Information

Sample Program: 10 sets minimum, single color

Stock Orders: 30 sets minimum, mixed colors

Private Label Orders: 100 sets minimum, mixed colors

Custom Sample Development: Approximately 15 days, subject to project requirements

Logistics

FAQ

1. What vehicles are compatible with this seat-cover set?

The set is intended for compatible 5-seat cars, SUVs, trucks and passenger vehicles. Because it is a universal-fit product, seat dimensions, headrest structure and rear-seat configuration should be checked before ordering.

2. What does the complete set include?

The set includes two front backrest covers with headrest covers, two front seat-base covers, two rear backrest covers with headrest covers and one rear long bench cover, plus installation accessories.

3. What material is used?

The main construction consists of leatherette, high-resilience sponge, non-woven fabric and an anti-slip silicone bottom layer.

4. What is the rear seat width range?

The rear long bench cover is designed for approximately 50-56 inch seat widths. Actual compatibility depends on the shape and structure of the vehicle's rear seat.

5. Are side airbags considered in the front-seat design?

The front covers include a reserved area around the side-airbag position. Compatibility must be checked for the specific vehicle, and the cover should not interfere with the original airbag deployment path.

6. Are storage pockets included?

Yes. The front seatback covers include storage pockets for small items such as phones, keys, documents and magazines.

7. What colors are available?

The standard color options are Black, Brown, Pink and Red. Additional color requirements can be discussed for custom production.

8. Can the product be customized?

Yes. Selected projects can include custom colors, stitching details, logo application, private-label packaging and bulk production.